|
Adobe Acrobat Reader v.
5 or newer is required in order to view these files. You can download Acrobat Reader software for free by clicking
here.
Terminal
Blocks:
Power
Distribution Assemblies:
-
GTP Series:
Compact power distribution assemblies
with ground terminal bonded to enclosure, and removable insulating feet to isolate robot from ground currents.
-
G2D
Series: Power distribution assemblies with MB-2 series power blocks in an enclosure built to GM standards.
-
P2H
Series: Power
distribution box with MB-2 series power blocks,
designed to distribute line or welding power in industrial applications.
-
P3H
Series:
Power distribution box with MB-3 series power
blocks,
designed to distribute line or welding power in industrial applications.
-
4330 Series
Interlock Disconnects:
Flush
mount interlock assemblies that do not allow plug to be engaged or
disengaged under power.
Cable
Grips:
-
7000
Series Cage Bushing: Syndevco
Cage Bushings provide a low cost design for oval or round cable strain
relief.
-
2490
Series Split Bushing: Syndevco
split bushings maintain a firm grasp of all cables in a pass through
water resistant device.
-
3000
Series Cable Strain Aid: The
3000 Series Cable Strain Aid provides optimal Strain relief for
maximum cable life, its superior design controls the bend radius of
Transgun primary cable.
-
7000-CP
Series Cover Plates: Syndevco
cover plates provide a water tight seal over the 5 hole pattern used
on 7000 Series Cage Bushings.
Power
Cables:
-
2446 Tap Switch and Cable:
The Syndevco Tap
Switch is a great solution for a plug-in resistance welding transformer
primary service system. Featuring a waterproof, non-metallic design with no
moving parts.
-
RF Series
Transgun Panel Mounts: Industrial strength Rapid Change connectors where the male end carries
the load, made with insulated contacts for maximum safety.
-
RF Series Cable Assemblies:
Industrial strength Rapid Change connectors where the male end carries
the load, made with insulated contacts for maximum safety. Urethane strain
relief used to maximize cable life.
-
C2 Series
Transgun Panel Mounts: Economical receptacles enable quick connecting to a transgun or power
distribution box.
-
C2
Series
Transgun
Cables: Industrial Strength connectors, with urethane strain reliefs for longer
service life.
-
SGL Series Cable Assemblies:
SGL series cable
assemblies are used as a primary Trans-Gun power cable. Straight and 90
degree versions available.
-
8000 Series Two Plug Plug & Receptacle: Connectors designed to meet the increasing need for
quick, easy changes in power distribution. Insulated with a high strength
polymer, with copper contacts that accommodate up to a 250 MCM cable.
Fluid
Products:
-
H
Series Manifolds: Compact manifolds with a variety of ports, port sizes, thread types,
material, and mounting options.
-
Wye
Series Manifolds:
Brass compact wye manifolds with two or three secondary ports, easily
mounted with 1/4 or M6 bolts.
-
4400 Series Water Control
Valves: Syndevco has developed a variety of water control valves to immediately
suspend water flow in the event of a ruptured supply or return water line or
worn out weld caps.
Robot Dressout
Components:
-
9950
Series Clamping System: The
9950 series clamping system is light weight, and non conductive, used
for clamping or routing air hoses, water hoses and electric cable.
-
UH Series
Utility Clamp:
High capacity hinged clamp with
quick release or bolt clasp. Available in basic or swivel/ stationary
mounting.
-
UH Series
Utility Clamp Inserts: Inserts used in conjunction with UH Series Clamps, available with a variety of
inner diameters and configurations
-
LH Series
Utility Clamp:
High capacity hinged clamp with
quick release or bolt clasp. Available in basic or swivel/ stationary
mounting.
-
LH Series
Utility Clamp Inserts: Inserts used in conjunction with UH Series Clamps, available with a variety of
inner diameters and configurations
-
SA
Series Brackets:
Heavy duty brackets that offer the greatest flexibility to route hoses
and cables anywhere on a robot.
-
SB Series
Boom Bars:
Boom Bars are an economical, flexible method of providing a mounting
point on any robot to allow for dressing.
-
SC
Series
Star Clamp:
Flexibility of mounting every 45 degrees around a Boom Bar along with
various mounting of other clamps and brackets.
-
SD
Series
Brackets:
Secure brackets that mount around axis points to assist in efficient,
flexible dressout of robots.
-
Velcro
Buckle Straps: Industrial strength
buckled velcro straps securely hold hose, and cord bundles together.
-
RC Corrugated Tube/ WB
Wear Bands: Protect
and control utilities for long service life.
-
WS Series Wear Sleeves: Protect
utilities for long wear and low downtime. Cut, tear, and abrasion resistant
removable wear sleeves.
Robot Dressout
Assemblies:
-
SS Spring
Retract Robot Dress Solutions:
Easy and minimal adjustments to match configuration and robot path of
highly articulating robots.
-
FS Floating
Robot Dress Solutions: Offers greatest
amount of protection of utilities. Flexible components to match
configuration and robot path.
-
Densification Packages: Syndevco
offers a variety of Densification Packages to accommodate different
robot applications, i.e. arm mount, hip mount, manual, pedestal welders
or material handling units.
-
Robot
Dress Modules: Robot dress components are designed in modular assemblies to increase usage of
common components and decrease assembly time.
Control Assemblies and
Special Products:
-
5000 Series LED Light: The 5000 series LED
lights are an excellent replacement of pilot lights where red and green are
required.
-
Marquee
Assemblies: Syndevco's Marquee is a product which works in conjunction with other
equipment to provide continuous monitoring of a production line.
-
Runbar/ Palm Button
Assemblies:
Stand mount or
table top mount assemblies are ergonomically designed to provide safety and
comfort.
|
